Faucet Installation and Repair
Aerator
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:27An aerator, or faucet aerator, is a small device that usually has a screen which attaches to the faucet at the point that the water comes out. Without an aerator, the water will come from the faucet in one rushing stream.
The aerator causes the water to be dispersed in many tiny droplets, this helps to conserve water and also, makes the water feel ‘softer’ and less harsh in the stream as it comes out.
Aerators are Simple to Install
Faucets and Sinks Q and A
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:19Q. I recently installed a new double vanity and faucets into a new bathroom. When I turn on the taps, for a few seconds the water is milky. This comes from both hot and cold through both sets of taps. Does the faucet cause this? I don't have the same thing from the shower or bath. Is it anything to be concerned about?
A. It could be a residue from the piping. Or, you are not used to the new aerators. It should not be a problem.
Salvaging That Unreplaceable Faucet Stem
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:14I have an outside shower that the family uses all summer long. The faucet stems are old and the flat ends (that support the washer) have broken and present a partial flat end thereby making it impossible to place even pressure on the washer and seat. Therefore the darned thing leaks no matter how often the washers are replaced and replaced and replaced! Drilling a hole in the middle of a penny (pennies are NOT considered legal tender, so this is a lawful act) and screwing the penny into the stem firmly, makes it easy to grind it on a grinding wheel to the appropriate size.
How to Repair a Leaking Faucet
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:09There are many faucets on the market. The single most common mistake is not taking the faucet or the part to be replaced with you when buying the new parts. Before working on any faucet turn the water off and open the lines to drain into the sink. Cover the sink with a towel or cloth to protect it from tools that may be dropped and to prevent the small parts from going into the drain. Wrap the jaws of wrenches with tape to protect the finish of the faucet.
Repair a Leaky Washer Type Faucet
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:08If you're not into water torture, then you probably can't stand the drip, drip, drip of a leaky faucet. Fortunately, you don't need to call a plumber to save you. These steps detail how to fix the leak in a washer-type faucet in no time.
Washer-type faucets work with a rubber or composition washer that closes onto a metal washer seat. When the washer becomes hardened, worn or the washer seat wears, it causes the faucet to leak. You can close the faucet tighter to stop the leaking temporarily, but this increases the internal damage to the faucet. Here's how to fix it.
Repair a Leaky Faucet
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:07Faucets are sold in many different makes and models, but the common ones fall into just a few types. You'll find only two basic kinds of faucets; washer-type (or compression) faucets and washerless faucets.
REPAIRING A LEAKY WASHER-TYPE FAUCET Faucets are replaced for a variety of reasons. There are several things to look out for when choosing a new faucet. The hole patterns of your old faucet should match the pattern of the new faucet. If there is any doubt about the pattern, take the old faucet with you or measure carefully for the hole placement. Step 1: Cut water supply off at the shut off valves. These are usually under the sink; if not cut the water off to the home from outside at the main water valve. Here are tips and instructions on how to replace sink, bath and shower faucets. Following these and manufacturer instructions can help you save time, money and effort. It can also help you end up with a neater, more satisfactory installation. In this document you will find information about: Faucets, like seemingly everything else in life, go in and out of style. Even if your old faucet is working just fine, you might come under some pressure to change faucets just so your kitchen or bathroom can reflect the latest fashion. Lucky for you, faucets are available in a broad price range - all the way from less than $20 for one made primarily of plastic all the way to $300 or more. The more expensive faucet should be made mainly of metal (brass) and will come with a multi year or even a lifetime warranty. So keep in mind when picking your new faucet, you do get what you pay for. Repairing a Ball Type Faucet In a ball faucet, moving the ball opens and closes passages inside the ball that control water flow. Since there are a lot of parts inside a ball faucet, they are more prone to leaking than other faucet designs. Ball faucet repair kits contain replacement parts but not usually a ball mechanism, since the ball itself is so rarely the cause of any problems. However, replacement balls are available. You Might wanna Check this out
More on Replacing a Faucet
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:05
How to Replace a Faucet
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:03
Installing or Replacing a Faucet
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:02
Faucet Types and How to Repair Them: Ball and Disc
Submitted by GreenGardenChic on Mon, 12/28/2009 - 15:00
Who's online
Online users
Best Price On the Web
